Need Help? Hire Us Now!

 

We have stumbled on this post pertaining to A Step-by-Step Guide to Installing a Bathtub down the page on the internet and think it made good sense to talk about it with you on this page.

Mounting a bath tub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and often, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably hard project. If the old tub is conveniently obtainable, the job can relocate easily; if you have to open up a wall to get rid of the old tub and also position the brand-new bathtub, the job is a lot harder. In either instance, the job is within a residence handyman's skills, although you will certainly require a helper to vacate the old tub as well as embeded in the new one. Make certain you have actually certified yourself for the job as well as are comfortable trying it. As opposed to working with a professional to take control of a halfway-completed task, it is much better to think about utilizing one before you begin. Possibilities are you might require a professional plumber to make tube connections.
This short article will certainly aid you mount a brand-new tub in your washroom if you have actually already purchased a new bathtub as well as don't require to alter the arrangement of your previous supply of water pipes.
Your devices and product checklist should consist of the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Measuring tape


• Pipe Caps


 

Planning for the Installation

To start with, the supporting framework provided with the bathroom ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to ensure that if the tap features a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets unit to prevent strain on the tub.
Fit the adaptable tap ports to the bottom of the two faucets making use of 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize all of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its final position.

 

 

Removing Old Touches

If you need to replace old taps with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the water system. After doing so, activate the faucets to drain pipes any water staying in the system. The process of removing the existing taps can be quite problematic due to the restricted access that is typically the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. When the supply pipelines have actually been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming throughout this process. As soon as the taps have been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing compound.
Before moving on to fit the brand-new taps, compare the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.

 

 

Installing the Tub

Utilizing the two wooden boards under its feet, put the bathtub in the needed placement. The wood boards are useful in uniformly spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four little factors.
The next objective is to make sure that the tub is leveled all round. This can be attained by inspecting the level and also adjusting the feet on the bath tub until the level checks out degree.
To install faucets, fit all-time low of the outermost versatile tap connector to the suitable supply pipe by making a compression join; after that do the very same for the other tap.
Switch on the water supply and also inspect all joints and also brand-new pipework for leaks and also tighten them if needed. Fill the bathtub as well as also examine the overflow outlet as well as the typical electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the maker's user's manual. Tiling and also sealing around the tub must wait till the bath tub has been utilized a minimum of when as this will certainly resolve it right into its final setting.

 

 

Suitable New Taps

If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end gives a connection to the existent supply pipes.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the tap in the placing opening in the bath/basin making certain that the washing machines are in area in between the faucet and the sink. Secure the tap in place with the manufacturer given backnut. As soon as the faucet is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular tap adapters. The former type needs to be linked to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.

 

 

Tiling Around the Bathtub

In the location where the bath satisfies the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to split an inflexible seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, causing issues with moisture as well as possible leakages to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to always load the bathtub with water prior to securing, to enable the activity experienced when the bathtub is in use. The sealant can fracture fairly early if you do not take into account this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly available on the market. It is advisable to fit the tiles making use of waterproof or water resistant sticky and grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Hopefully you enjoyed reading our post on Tools You Need to Install a New Bathtub . Thanks for taking the time to read through our piece. Do you know about another person who is interested by the topic? Be sure promote it. I praise you for your time. Kindly visit our site back soon.

Request Service